| AUDIO |
|
| |
Internal Frequency Response |
± 0.1 dB 1 Hz
to 70 kHz |
| |
Basic Pre-emphasis
Accuracy |
±
0.1 dB 20Hz to 15KHz disregarding any audio processing alterations |
| |
THD
(for all signals below clip threshold) |
Demodulated
MPX output, 0dB 1KHz tone input, THD <0.05% |
| |
Active
Process Distortion
(typical worst case) |
Demodulated
MPX output, 0dB 1KHz tone input, CHR factory preset, THD <0.5%
Note: This typifies peaks only, and not signals below clip threshold. |
| |
Stereo Output Noise
(left or right channel) |
CHR
Factory preset, 20Hz-20KHz measurement bandwidth
ref 100% modulation = -70dB |
| |
Mono Output Noise |
CHR Factory preset,
20Hz-20KHz measurement bandwidth
ref 100% modulation = -71dB
|
| |
Processing Peak
Overshoot |
Less
than 1.5% above 100% modulation |
| |
System Stereo Separation |
Greater
than 65dB 20Hz to 15KHz |
| ANALOG
AUDIO INPUT |
|
| |
Configuration |
Left
and Right |
| |
Impedance |
10K
Ohms |
| |
CMRR |
>70dB
50Hz - 20KHz |
| |
Sensitivity |
-24dBu
to +10dBu for nominal input level |
| |
Maximum Input Level |
+27dBu |
| |
Connector |
XLR
3-Pin Female EMI Suppressed. Pin 1 chassis ground, Pins 2 &
3 electronically balanced, floating and symmetrical. Pin 2 in
in phase with multiplex and digital output |
| |
Type |
Transformerless, differential
servo balanced with 4th order RF filter |
| ANALOG
AUDIO OUTPUT |
|
| |
Configuration |
Left
and right. Flat or pre-emphasized |
| |
Source Impedance |
62 Ohms
electronically servo balanced |
| |
Load Impedance |
600
Ohms or greater balanced or unbalanced. Termination not required. |
| |
Maximum Output Level |
+24dBu
onto 600 ohms balanced |
| |
Connector |
XLR
3-Pin male, EMI Suppressed. Pin 1 chassis ground, Pins 2 &
3 electronically balanced, floating and symmetrical. Pin 2 in
in phase with multiplex and digital output. |
| DIGITAL
INPUT |
|
| |
Configuration |
Two-channel
AES/EBU standard. Pre-emphasized or non pre-emphasized. |
| |
Sampling Rate |
32,
44.1, and 48KHz auto detect and lock |
| |
Connector |
XLR
3-Pin male EMI Suppressed.
Pin 1 chassis ground, Pins 2 & 3 transformer balanced and
floating |
| |
Input Data Size |
20-bits |
| |
Input Frequency
Response |
1 to
20KHz +/- 0.1dB |
| DIGITAL
OUTPUT |
|
| |
Configuration |
Two-channel
AES/EBU standard |
| |
Sampling Rate |
Input
clock-slaved or independently selected at 32, 44.1, or 48KHz.
|
| |
Connector |
XLR
3-Pin Female EMI Suppressed. Pin 1 chassis ground, Pins 2 &
3 transformer balanced and floating |
| |
Output Data Size |
20-bits |
| |
Output Frequency
Response |
1Hz
to 20KHz +/- 0.1dB |
| COMPOSITE
BASEBAND OUTPUT |
| |
Configuration |
Single
output with output level control |
| |
Source Impedance |
10 ohms
suitable to drive long or short coaxial cable |
| |
Load Impedance |
50 ohms
or greater |
| |
Output Level |
Adjustable
from 0 to 13V peak-to-peak with multiturn output control |
| |
Connector |
BNC,
EMI Suppressed. Floating over chassis ground at RF frequencies. |
| |
Max. recommended
cable length |
100ft
RG58A/U or equivalent. |
| |
Pilot Level |
Adjustable
7% to 11% mix |
| |
Frequency Stability |
Pilot
and subcarrier +/- 10ppm -50 to +80 deg C ambient |
| |
Stereo Generator
Technology |
Aphex
patented Parallel Path Digital Modulation (PPDM) |
| |
Pilot Phase Error |
0 degrees
guaranteed indefinitely by PPDM design |
| |
Spurious Output |
better
than -72dB above 55KHz, typical <-85dB |
| |
Subcarrier Rejection |
better
than -60dB |
| |
Harmonic Distortion |
Better
than 0.003% within stereo generator |
| |
Intermodulation
Distortion |
Better
than 0.003% within stereo generator |
| |
Frequency Response |
1Hz
to 15KHz +/1 0.1dB, -3dB at 0.159Hz and 15.5KHz |
| REMOTE
CONTROL INTERFACE |
| |
Configuration |
RS232
standard serial port |
| |
Connector |
DB-9
male |
| |
Control capability |
All
FM Pro functions and parameters |
| |
Connectability |
Null
modem cable to P.C. or modem cable to modem |
| |
Modem Compatibility |
U.S.
Robotics Sportster. For others check with factory. |
| POWER |
| |
Line Voltage Input |
77 to
266VAC 50-1000Hz automatic (no selection required) |
| |
Power Requirements |
50 Watts |
| |
Safety Standards |
CE,
UL, CSA, VDE |
| PHYSICAL |
|
| |
Front Panel Size |
Standard
2-RACK UNIT (3.5" vertical) 19-inch panel |
| |
Dimensions |
19"W x 3.5"H
x 13.125" overall Depth (482.6mm
x 88.9mm x 334mm)
allow for connectors and wire dress |
| ENVIRONMENTAL |
|
| |
Operating Temperature
Range |
32-122
deg. F (0-50 deg C) |
| |
Humidity |
0 to
95% RH, non-condensing |
 |
 |
 |
 |
 |